When to Replace an RO Filter: Signs and Tests
Back to blog

When to Replace an RO Filter: Signs and Tests

Use taste, flow, service dates and a TDS test to decide whether your RO system needs maintenance.

November 11, 2026

Is Your RO System Due for Attention?

Your RO faucet tastes different, runs slowly or has gone too long without maintenance. This guide explains when to replace an RO filter, which warning signs point to membrane failure and how to check performance with a TDS meter. You will also learn when a storage tank or valve may be at fault and when a leak needs professional attention. Service dates help, but your water conditions and the system’s measured performance should guide the decision.

Signs Your RO Filter May Need Replacement

Taste and odor changes often appear before flow stops. A bleach-like, chemical or metallic taste can mean the carbon stages are saturated and chlorine is reaching later stages. A salty or bitter taste may indicate that the RO membrane is no longer rejecting dissolved minerals effectively.

Musty, earthy or rotten-egg odors need prompt investigation. They may come from organic matter or biofilm in an exhausted cartridge, filter housing, polishing filter or storage tank. University of Nebraska–Lincoln Extension notes that rotten-egg odors can have several causes, so do not assume a new cartridge will always solve the problem.

A noticeable drop in flow or a prolonged refill time signals a restriction within the system, according to Wellesley College’s RO maintenance guide. Check for these signs:

  • The dedicated faucet has slowed to a weak trickle even after the tank has had time to refill.
  • The tank takes much longer than its usual two to four hours to replenish.
  • The water tastes or smells wrong shortly after a cartridge change.
  • You see cloudy residue, discoloured filter media or contamination inside a clear housing.
  • The system has exceeded its maintenance date and you do not know when it was last serviced.

A new taste alone does not prove that local tap water is unsafe. Check the system, review the cartridge dates and test the source and treated water if the change continues.

Standard Replacement Timeline for Multi-Stage RO Systems

Each stage performs a different job, so an entire RO system does not follow one replacement date. Check the manufacturer’s instructions first because cartridge size, household use and feed-water quality affect service life.

  • Sediment pre-filter: usually every 6 to 12 months. High sediment levels may shorten that interval to 3 to 6 months.
  • Carbon pre-filters: usually every 6 to 12 months. Timely replacement helps stop chlorine from damaging a thin-film composite membrane.
  • Post-carbon polishing filter: commonly every 12 months, or sooner if taste returns.
  • RO membrane: often every 2 to 5 years, based on rejection performance rather than age alone.
  • Pressurized storage tank: often 5 to 10 years, although pressure or bladder failure can require earlier replacement.

Write the installation date on each new cartridge and keep a service log. Record the tap-water and RO-water TDS after replacement as a baseline for future tests instead of relying only on a calendar reminder.

A sediment pre-filter canister installed on a residential copper water supply line in a basement.

How North Jersey Water Conditions Accelerate Wear

Feed-water conditions can shorten cartridge life. Mineral hardness contributes to scale on the membrane, while rust and pipe scale can load the sediment stage. Chlorine consumes carbon-media capacity, and runoff after heavy rain can increase the sediment and organic material reaching treatment systems.

Cold feed water also reduces RO production. During a North Jersey winter, water entering the system may be around 40°F to 50°F, and output can fall by 40% to 50%. A seasonal slowdown does not automatically mean the membrane has failed. Compare the flow with previous winters and check the pre-filters before replacing the membrane.

At Crescent Sewer & Drain Cleaning Service, we recommend choosing filtration around your home’s measured water conditions rather than a generic regional assumption. We do not treat unusual taste as proof that municipal water in Hillside or nearby communities is unsafe. Testing and inspection provide a sounder answer. Our licensed and insured team provides whole-home water filtration installation, with the setup selected for the property and connected to its existing plumbing.

If you are deciding between a drinking-water unit and broader treatment, review the signs that a whole-home water filter may be appropriate.

How to Test RO Filter Performance with a TDS Meter

A handheld digital TDS meter provides a quick way to measure how well the membrane rejects dissolved material. It does not identify individual contaminants or prove that water is microbiologically safe, but it can reveal a decline in membrane performance.

  1. Run both the regular cold tap and RO faucet for several minutes. This reduces the effect of TDS creep, in which readings rise while the system sits idle.
  2. Collect separate clean samples of untreated tap water and RO water. If the system has an alkaline remineralisation stage, collect the RO sample before that cartridge when possible.
  3. Measure the tap-water TDS, rinse the meter and then measure the RO-water TDS.
  4. Subtract the RO reading from the tap reading. Divide the result by the tap reading, then multiply by 100.

Under the NSF/ANSI 58 performance standard, an intact thin-film composite membrane typically rejects 90% to 98% of dissolved minerals and inorganic contaminants. A result below roughly 80% to 85%, confirmed after installing fresh pre-filters and repeating the test, is a strong replacement signal.

Compare results under similar conditions. A change in source-water TDS, temperature or system pressure can affect the reading. If health-related contaminants are the concern, use appropriate laboratory testing rather than relying on TDS alone.

Troubleshooting Leaks, Bladders and Run-On Drains

Not every weak stream is caused by an expired cartridge. Listen for water running continuously to the drain hours after the storage tank should be full. Persistent drain flow can indicate a failed automatic shut-off valve, clogged flow restrictor or leaking check valve.

A tank that feels full but provides little water may have lost its air charge or suffered an internal bladder failure. Check the Schrader valve at the base using the tank manufacturer’s procedure. If water comes from that air valve, the bladder has failed and the tank normally needs replacement.

Inspect beneath the sink for moisture around housing threads, O-rings, quick-connect fittings and the membrane housing. O-rings can flatten or become brittle, creating slow leaks that damage cabinets before standing water appears. Shut off the RO feed if you find active leaking. Cracked housings, internal manifold leaks and damaged fittings need professional component replacement rather than repeated tightening.

A plumbing technician seen from behind examining a whole-home water filtration tank in a basement.

Protecting Your Water Supply and Plumbing

Clean drinking water matters to your family’s health and peace of mind, but the right treatment depends on the water entering your home, your plumbing and what you want to reduce. If taste, odor or sediment affects several fixtures, a whole-home approach may be more suitable than continuing to troubleshoot one under-sink unit.

Crescent Sewer & Drain Cleaning Service begins with an inspection to look for the cause of low pressure, leaks or filtration concerns before a small problem damages the property. We offer free inspections and install complete whole-home filtration systems for customers in North and Central Jersey. Our team is also available 24/7 for major leaks and other plumbing emergencies.

Arrange a Water and Plumbing Inspection

If your RO system is leaking, pressure has dropped or you want to assess whole-home filtration, schedule a free inspection with Crescent Sewer & Drain Cleaning Service. We are based in Hillside, NJ; call (973) 277-1014 or email greatersword7@gmail.com. For an active major leak, shut off the nearest safe water valve and call us for 24/7 help.

SHARE ON SOCIAL MEDIA

You might also like